615 reviews analysed
1. Hard-to-Find Fastener 014973281267 281267, 1/4-20″, 12 Anchors
Description
We stock a wide variety of fasteners ideal for many applications around the home, farm, business, automotive, and in industry. Most of our fasteners have a light zinc plating over steel giving a more rust resistant finish. We also sell coated and stainless products for additional rust resistance. We stock many grades of fasteners ranging from low carbon steel on up to hardened, heat treated steel. Not all fasteners are applicable for all applications so be certain to test thoroughly and get the opinion of a licensed builder or certified building or structural engineer before relying on these fasteners for any situations where failure would result in damage to property or person.
2. The Hillman Group 375297 Hex Washer, Head Slotted Tapper Concrete Screw Anchor, 1/4 x 3-1/4-Inch, 100-Pack
Description
Product Description
RAWL brand. Concrete screw anchors. Hex washer head. 100-pieces per pack. Carbide bit included. Ceramic-coated. ACQ approved.
From the Manufacturer
State of the art thread design cuts into concrete. Tapper screws are designed for fastening applications in concrete, block, and brick. Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, hurricane shutters, and more. Tapper screws are perfect for indoor and outdoor use. For light to medium duty applications.
3. Hurricane Hardware Stainless Steel Phillips Combo Drive Stainless Steel Sidewalk Bolt Kit with Masonry Anchors – 24 Pieces
Feature
- 1/4″-20 x 1-1/2″ Phillips Slotted Combo Drive Sidewalk Bolts 18-8 Stainless Steel – 12 pieces
- 1/4″-20 Machine Screw Masonry Anchors – 12 Pieces
- Commonly used for storm windows and shutters to anchor into brick or masonry wall
- Fixtures can be removed or replaced without sacrificing holding power
- Corrosion resistant stainless steel screws with caulking type anchors designed to provide a quick setting in brick, concrete or stone
4. Red Head ITW 1/4 X 3-1/4" Hwh 410 ss Buildex Tapcon Stainless Steel Concrete Anchors
Feature
- FREE SHIPPING-All orders $25 or more ship for free
- buy more and save more
- BIT INCLUDED IN EACH BOX-Proper bit equals improved holding values and reduced cost
- FLAT PHILLIPS HEAD–Can be driven with Phillips Screw Driver
- SELF-TAPPING-Taps threads directly into masonry and requires no other anchor
- DIAMOND POINT-Easier to drive the screw to save time
Description
Applications
The anchor is made from 410 Stainless Steel, and is Silver Climaseal Coated. This anchor is designed for use in Concrete, Block, and Brick.
Environment
The anchor is designed for use in a Moist environment.
Head Style
The anchor is a Hex Washer head and is designed to allow the head to sit on top of the surface of the item being attached.
Hole Diameter/Bit Diameter
The anchor requires a 3/16″ hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Driver Required
A 5/16″ is required for driving the anchor into the base material.
Diameter of Anchor
The diameter of the anchor is 1/4″.
Length Anchor
The length of the anchor is 3-1/4″
Thread Length
The length of the threads on the anchor is 1-3/4″ in length.
Minimum Embedment
The minimum anchor embedment into the concrete is 1″. Therefore, the anchor must be installed so that a minimum of 1″ of the anchor is embedded into the concrete.
Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-1/4″. This will ensure that the minimum embedment of 1″ will be met.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4″ diameter anchor requires the hole in the fixture to be 5/16″.
Spacing between Anchors
Each anchor must be spaced a minimum distance of 4″ from each other when measured center to center.
Edge Distance
It is very important not to install the anchor any closer than 3″ from an unsupported edge of the concrete.
5. CONFAST 1/4" (Inside/Screw 1/4-20 Diameter) Machine Screw Anchor with 1 Setting Tool (100 per Box)
Feature
- SHALLOW EMBEDMENT OPPORTUITIES-Less time required to drill hole
- NATIONAL COARSE THREADS-Bolts and threaded rod is most common type available
- INTERNAL THREADS Easy-removabilityWORKS IN MOST MASONRY MATERIAL-Consistent holding values in wide variety of base materials
- REQUIRES THE USE OF A SETTING TOOL-Setting tool allows for proper positive expansion of the anchor
Description
Applications
The anchor is made from Anchor Body Antimonial Lead Alloy/Cone Zamac Alloy. This anchor is designed for use in Concrete, Block, and Brick.
Environment
The anchor is designed for use in a Moist environment.
Head Style
The anchor is a head
Hole Diameter/Bit Diameter
The anchor requires a 1/2″ hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Driver Required
A is required for driving the anchor into the base material.
Diameter of Anchor
The diameter of the anchor is 1/4″.
Length Anchor
The length of the anchor is 7/8″
Thread Length
The length of the threads on the anchor is in length.
Minimum Embedment
The minimum anchor embedment into the concrete is 7/8″. Therefore, the anchor must be installed so that a minimum of 7/8″ of the anchor is embedded into the concrete.
Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is . This will ensure that the minimum embedment of 7/8″ will be met.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4″ diameter anchor requires the hole in the fixture to be 9/16″.
Spacing between Anchors
Each anchor must be spaced a minimum distance of 5″ from each other when measured center to center.
Edge Distance
It is very important not to install the anchor any closer than 2-1/2″ from an unsupported edge of the concrete.
6. National Hardware N179-812 4005BC Smooth Rod in Zinc plated
7. The Hillman Group 375313 Flat Head Phillips Tapper Concrete Screw Anchor, 1/4 x 4-Inch, 100-Pack
Description
Product Description
State of the art thread design cuts into concrete. Tapper screws are designed for fastening applications in concrete, block and brick. Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, hurricane shutters and more. Tapper screws are perfect for indoor and outdoor use. For light to medium duty applications.
From the Manufacturer
State of the art thread design cuts into concrete. Tapper screws are designed for fastening applications in concrete, block, and brick. Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, hurricane shutters, and more. Tapper screws are perfect for indoor and outdoor use. For light to medium duty applications.
8. The Hillman Group 375286 Hex Washer, Head Slotted Tapper Concrete Screw Anchor, 3/16 x 1-1/4-Inch, 100-Pack
Description
Product Description
Rawl, 100 pack, 3/16 inch x 1-1/4 inch hex washer head tapper concrete screw anchor with bit, blue perma-seal coating, 1 inch embedment, ultimate tension 4,000 psi concrete 730 lb, ultimate shear 4,000 psi concrete 1,090 lb.
From the Manufacturer
State of the art thread design cuts into concrete. Tapper screws are designed for fastening applications in concrete, block, and brick. Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, hurricane shutters, and more. Tapper screws are perfect for indoor and outdoor use. For light to medium duty applications.
9. ITW Brands 24515 225 Pack, 1/4" x 1-1/4", Tapcon Hex Washer Head Concrete Anchor
Description
225 pack, 1/4″ x 1-1/4″, Topcon hex washer head concrete anchor, designed for fastening applications in concrete, block & brick, approved for treated lumber, use to attached electrical equipment, downspout straps, hose reels, flagpoles & hurricane shutters, indoor & outdoor applications, building code approved.
10. The Hillman Group 375309 Flat Head Phillips Tapper Concrete Screw Anchor, 1/4 x 2-1/4-Inch, 100-Pack
Feature
- State of the art thread design cuts into concrete
- Tapper screws are designed for fastening applications in concrete, block and brick
- Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, Hurricane shutters and more
- BLUE Parma-Seal coated
- For use with treated lumber
- Building code approved
Description
Product Description
State of the Art thread design cuts into concrete. Tapper screws are designed for fastening applications in concrete, block and brick. Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, hurricane shutters and more. Tapper screws are perfect for indoor and outdoor use. For light to medium duty applications.
From the Manufacturer
State of the art thread design cuts into concrete. Tapper screws are designed for fastening applications in concrete, block, and brick. Use Tapper screws to attach electrical equipment, two by fours, downspout straps, hose reels, flag poles, hurricane shutters, and more. Tapper screws are perfect for indoor and outdoor use. For light to medium duty applications.
Conclusion
By our suggestions above, we hope that you can found Concrete Anchor Hurricane for you.Please don’t forget to share your experience by comment in this post. Thank you!
