The Best Micro Swiss Cooling Block

This is Micro Swiss All Metal Hotend kit for Wanhao Duplicator 6. This upgrade includes a modified thermal barrier tube and modified nozzle with modified cooling block. Thermal barrier tube is made from 2 different materials. The lower thermal break is made from stainless steel, and the colder upper part is made from aluminum. Stainless steel was used for thermal break because it offers low thermal conductivity, and aluminum was used for the upper portion because it has a lot better thermal conductivity, to carry away any heat from the filament. All metal hotend will let you print at much higher temperature then possible with original PTFE lined one. Another benefit of an all metal hotend design is more consistent melt chamber control. During slow extrusion rate, in PTFE lined hotend, transition zone from solid to molten plastic tends to creep upward creating more stringy prints. With all metal design a transition zone is always constant, being located right at the heat break. With fast extrusion rate, PTFE tube doesn’t have enough thermal conductivity to properly melt all the plastic coming out. On original extruders that limitation happens around 60 mm/s, depending on nozzle size. All metal hotend solves this problem, plastic is surrounded by thermally conductive nozzle throughout its length.

This is redesigned cooling block for Wanhao i3 with the following improvements: Slotted Clamping system, No set screw to ding and damage thermal tube, Significantly better heat transfer (this is a big one!!!), Easier disassemble and adjustments, Tight control on bore diameter, This cooling block will work with original PTFE lined hotend, and with our Micro Swiss MK10 Allmetal Hotend kit.

This is Micro Swiss All Metal Hotend kit with redesigned cooling block for Wanhao i3 with the following improvements: Micro Swiss All Metal Hotend Kit Features: All metal hotend upgrade for MK10 style extruders. This upgrade includes a modified thermal barrier tube and modified nozzle with modified cooling block. Thermal barrier tube is made from 2 different materials. The lower thermal break is made from stainless steel, and the colder upper part is made from aluminum. Stainless steel was used for thermal break because it offers low thermal conductivity, and aluminum was used for the upper portion because it has a lot better thermal conductivity, to carry away any heat from the filament. All metal hotend will let you print at much higher temperature then possible with original PTFE lined one. Another benefit of an all metal hotend design is more consistent melt chamber control. During slow extrusion rate, in PTFE lined hotend, transition zone from solid to molten plastic tends to creep upward creating more stringy prints. With all metal design a transition zone is always constant, being located right at the heat break. With fast extrusion rate, PTFE tube doesn’t have enough thermal conductivity to properly melt all the plastic coming out. On MK10 extruders that limitation happens around 60 mm/s, depending on nozzle size. All metal hotend solves this problem, plastic is surrounded by thermally conductive nozzle throughout its length. STEP BY STEP INSTALLATION INSTRUCTION https://store.micro-swiss.com/pages/micro-swiss-all-metal-hotend

Micro Swiss Heater Block Upgrade with Silicone Sock for CR10 Printers
This is Micro Swiss aluminum upgrade upgrade with slotted clamping system for CR-10 family printers. 

Fits:

• Creality CR-10
• Creality CR-10-S5
• Creality CR-10-S4 
• Creality CR-10S
• Creality CR-10 MINI
• Ender 2
• Ender 3
• TronXY X5S
• MK7, MK8, MK9 Hotends

This is Micro Swiss All Metal Hotend kit with redesigned cooling block for Wanhao i3 with the following improvements: Micro Swiss All Metal Hotend Kit Features: All metal hotend upgrade for MK10 style extruders. This upgrade includes a modified thermal barrier tube and modified nozzle with modified cooling block. Thermal barrier tube is made from 2 different materials. The lower thermal break is made from stainless steel, and the colder upper part is made from aluminum. Stainless steel was used for thermal break because it offers low thermal conductivity, and aluminum was used for the upper portion because it has a lot better thermal conductivity, to carry away any heat from the filament. All metal hotend will let you print at much higher temperature then possible with original PTFE lined one. Another benefit of an all metal hotend design is more consistent melt chamber control. During slow extrusion rate, in PTFE lined hotend, transition zone from solid to molten plastic tends to creep upward creating more stringy prints. With all metal design a transition zone is always constant, being located right at the heat break. With fast extrusion rate, PTFE tube doesn’t have enough thermal conductivity to properly melt all the plastic coming out. On MK10 extruders that limitation happens around 60 mm/s, depending on nozzle size. All metal hotend solves this problem, plastic is surrounded by thermally conductive nozzle throughout its length. STEP BY STEP INSTALLATION INSTRUCTION https://store.micro-swiss.com/pages/micro-swiss-all-metal-hotend

This is a performance MK8 All Metal Hotend Upgrade. It includes a coated nozzle and coated thermal barrier tube. They are plated with a very low friction plating called TwinClad XT. TwinClad XT is a nickel composite coating designed to be very hard, corrosion resistant, and have good release properties against plastic. It offers one of the lowest coefficient of friction, better than nickel with PTFE co-deposit. The hardness makes this coating abrasion resistant. If you are working with abrasive Carbon Fiber, Stainless Steel, wood filled or any other metal filled filaments, this will greatly improve the life of your nozzle. Low friction will also prevent clogs in thermal barrier tube, a critical zone where plastic liquidizes. Dimension: *M6x1 Threads *Tubes: 26mm long *Nozzles: 13mm long

This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit our MK10 All Metal Hotend Kit. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube. It is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is a nickel composite coating designed for very low friction. It offers one of the lowest coefficient of friction, better then nickel with PTFE co-deposit. This coating is also very hard and abrasion resistant. If you are working with abrasive Carbon Fiber, Stainless Steel, wood filled or any other metal filled filaments, this will greatly improve the life of your nozzle.

This tube is an improvement over the stock MakerBot Replicator 1 and MakerBot Replicator 2 thermal barrier tube. It is made from stainless steel and plated with TwinClad XT coating. TwinClad XT is a very low friction Electroless Nickel composite coating, often used in injection molding because of it release properties. This high lubricity plating will prevent clogging in the critical zone of hotend, where filament liquidizes. It is also very hard and corrosion resistant. Great for high abrasion filaments like Carbon Fiber, Metal filled, Aluminates, etc.